How to use the pallet calculator
Start with one case. Enter its outside length, width and height in inches and its gross weight, which is the fruit plus the carton and liner. Then set your pallet size and the limits you work with: the tallest load your warehouse or carrier accepts, and the heaviest pallet your racks and forklifts can handle.
The calculator tries the case in every direction on the pallet, including mixed patterns where some cases are turned, and keeps the layout that fits the most cases per layer. It then stacks layers until it hits either the height limit or the weight limit, whichever comes first, and tells you which one stopped it.
How many cases fit on a pallet?
It depends on the case footprint and how tall you can build. A common 30 lb case of IQF fruit measures roughly 15.75 x 11.75 x 9 inches. On a 48 x 40 inch pallet that works out to 10 cases per layer in a mixed pattern. At a 60 inch maximum height with a 6 inch pallet, you get 6 layers, so 60 cases and about 1,900 lb per pallet.
Two things change the count the most. The first is the height limit: a few extra inches can add a whole layer. The second is overhang. Cases that hang over the edge of the pallet get crushed and can be refused at receiving, so this calculator never lets cases overhang.
Pallet sizes
| Pallet | Size | Where it's used |
|---|---|---|
| US standard (GMA) | 48 x 40 in | United States and Canada, most food distribution |
| ISO / Asia | 1200 x 1000 mm (47.2 x 39.4 in) | Asia, Latin America, many export loads |
| Euro pallet (EUR) | 1200 x 800 mm (47.2 x 31.5 in) | Europe |
How many pallets fit in a reefer container?
For standard 48 x 40 inch pallets loaded single stacked, these are typical counts. Reefer containers are a little narrower and shorter inside than dry containers because of the insulation and the refrigeration unit, so they hold fewer pallets than people expect.
| Equipment | Typical 48 x 40 pallet positions |
|---|---|
| 20 ft reefer container | About 9 |
| 40 ft reefer container | About 20 |
| 40 ft high cube reefer | About 20 |
| 53 ft reefer trailer | About 26 |
Exact counts depend on the equipment and how the pallets are turned, so treat these as a starting point and confirm with your carrier.
Floor space or weight: what fills a load first?
Frozen fruit is dense. A full 40 ft reefer of 30 lb cases often reaches the road weight limit before it runs out of floor space, especially if pallets are built tall. In the US, a loaded truck generally can't go over 80,000 lb gross, which usually leaves somewhere around 40,000 to 44,000 lb for cargo once you take off the tractor, chassis, container and reefer unit. The calculator compares both and shows which one sets your maximum.
If weight is the limit, building shorter pallets doesn't cost you anything and makes the pallets easier to handle. If floor space is the limit, taller pallets or a better case pattern get more fruit on the same truck.
Tips for building pallets of frozen fruit
- Leave room for air. Cold air needs to move around the load. Most reefer loads are kept below the red load line marked inside the container, and floors use T bar channels so air can flow under the pallets.
- Don't overhang. Cases hanging over the edge get crushed and can let warm air in.
- Stack corner on corner. Column stacking keeps the weight on the strongest part of the carton. Interlocking patterns are more stable but put more pressure on the case walls.
- Stretch wrap and corner boards. They keep the load square through ports, rail ramps and cross docks.
- Single stack frozen pallets. Double stacking crushes the bottom cases unless the cartons are built for it.
Plan your next order by the pallet
Our minimum order is one full pallet, and we can quote by the pallet, the truckload or the container. Use the result here to see how many cases make sense for you, then request a quote with the fruit and format you need.